Eth0 doesn't keep static IP - Raspberry Pi Forums

-

hi,
i've got raspberry 2 running huawei e173 , umtskeeper internet , device connected via ethernet. eth0 (theoretically) has static ip, after few hours, link lost temporarily , when comes on again, pi uses ipv4ll adress (169.254.214.51). restarting networking fixes this, again temporarily.
here's log of happens when link lost, have idea why happening and/or how can fix this?

code: select all

sep 18 01:02:20 raspberrypi dhcpcd[1614]: eth0: carrier lost sep 18 01:02:20 raspberrypi kernel: smsc95xx 1-1.1:1.0 eth0: link down sep 18 01:02:20 raspberrypi dhcpcd[1614]: eth0: deleting address fe80::15fe:e212:94fb:c751 sep 18 01:02:20 raspberrypi avahi-daemon[533]: withdrawing address record fe80::15fe:e212:94fb:c751 on eth0. sep 18 01:02:20 raspberrypi avahi-daemon[533]: leaving mdns multicast group on interface eth0.ipv6 address fe80::15fe:e212:94fb:c751. sep 18 01:02:20 raspberrypi avahi-daemon[533]: interface eth0.ipv6 no longer relevant mdns. sep 18 01:02:20 raspberrypi avahi-daemon[533]: withdrawing address record 169.254.214.51 on eth0. sep 18 01:02:20 raspberrypi dhcpcd[1614]: eth0: deleting route 169.254.0.0/16 sep 18 01:02:20 raspberrypi avahi-daemon[533]: leaving mdns multicast group on interface eth0.ipv4 address 169.254.214.51. sep 18 01:02:20 raspberrypi avahi-daemon[533]: interface eth0.ipv4 no longer relevant mdns. sep 18 01:02:20 raspberrypi dhcpcd[16950]: sending commands master dhcpcd process sep 18 01:02:20 raspberrypi kernel: smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup sep 18 01:02:20 raspberrypi dhcpcd[1614]: control command: /sbin/dhcpcd -k eth0 sep 18 01:02:20 raspberrypi dhcpcd[1614]: eth0: removing interface sep 18 01:02:20 raspberrypi kernel: smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup sep 18 01:02:20 raspberrypi kernel: ipv6: addrconf(netdev_up): eth0: link not ready sep 18 01:02:20 raspberrypi dhcpcd[1614]: eth0: adding address fe80::15fe:e212:94fb:c751 sep 18 01:02:20 raspberrypi dhcpcd[17112]: sending commands master dhcpcd process sep 18 01:02:20 raspberrypi kernel: smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup sep 18 01:02:21 raspberrypi dhcpcd[1614]: eth0: waiting carrier sep 18 01:02:21 raspberrypi dhcpcd[1614]: control command: /sbin/dhcpcd -k eth0 sep 18 01:02:21 raspberrypi dhcpcd[1614]: eth0: removing interface sep 18 01:02:21 raspberrypi kernel: smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup sep 18 01:02:21 raspberrypi kernel: ipv6: addrconf(netdev_up): eth0: link not ready sep 18 01:02:22 raspberrypi ntpd[580]: deleting interface #115 eth0, 169.254.214.51#123, interface stats: received=0, sent=0, dropped=0, active_time=7197 secs sep 18 01:02:22 raspberrypi ntpd[580]: deleting interface #113 eth0, fe80::15fe:e212:94fb:c751#123, interface stats: received=0, sent=0, dropped=0, active_time=14417 secs sep 18 01:02:22 raspberrypi ntpd[580]: peers refreshed sep 18 01:02:22 raspberrypi dhcpcd[1614]: eth0: adding address fe80::15fe:e212:94fb:c751 sep 18 01:02:22 raspberrypi kernel: ipv6: addrconf(netdev_change): eth0: link becomes ready sep 18 01:02:22 raspberrypi kernel: smsc95xx 1-1.1:1.0 eth0: link up, 100mbps, full-duplex, lpa 0x41e1 sep 18 01:02:22 raspberrypi dhcpcd[1614]: eth0: iaid eb:6a:5a:06 sep 18 01:02:23 raspberrypi dhcpcd[1614]: eth0: soliciting dhcp lease sep 18 01:02:23 raspberrypi dhcpcd[1614]: eth0: soliciting ipv6 router sep 18 01:02:24 raspberrypi avahi-daemon[533]: joining mdns multicast group on interface eth0.ipv6 address fe80::15fe:e212:94fb:c751. sep 18 01:02:24 raspberrypi avahi-daemon[533]: new relevant interface eth0.ipv6 mdns. sep 18 01:02:24 raspberrypi avahi-daemon[533]: registering new address record fe80::15fe:e212:94fb:c751 on eth0.*. sep 18 01:02:25 raspberrypi ntpd[580]: listen on 116 eth0 fe80::15fe:e212:94fb:c751 udp 123 sep 18 01:02:25 raspberrypi ntpd[580]: peers refreshed sep 18 01:02:28 raspberrypi dhcpcd[1614]: eth0: probing ipv4ll address sep 18 01:02:33 raspberrypi dhcpcd[1614]: eth0: using ipv4ll address 169.254.214.51 sep 18 01:02:33 raspberrypi dhcpcd[1614]: eth0: adding route 169.254.0.0/16 sep 18 01:02:33 raspberrypi avahi-daemon[533]: joining mdns multicast group on interface eth0.ipv4 address 169.254.214.51. sep 18 01:02:33 raspberrypi avahi-daemon[533]: new relevant interface eth0.ipv4 mdns. sep 18 01:02:33 raspberrypi avahi-daemon[533]: registering new address record 169.254.214.51 on eth0.ipv4. sep 18 01:02:34 raspberrypi ntpd[580]: listen on 117 eth0 169.254.214.51 udp 123 sep 18 01:02:34 raspberrypi ntpd[580]: peers refreshed sep 18 01:02:36 raspberrypi dhcpcd[1614]: eth0: no ipv6 routers available

have defined static address in /etc/dhcpcd.conf?


raspberrypi



Comments

Post a Comment

Popular posts from this blog

Connecting Raspberry Pi 2 to P10(1R)-V706 LED Dot Matrix - Raspberry Pi Forums

-
Image
hello everyone, name kedi.. make system connecting raspberry pi 2 , arduino uno arduino adc of 1 dust sensor sharp gp2y1010au0f , 4 gas sensor. want show decision of air quality system in running text @ p10 16x32 led dot matrix display. in raspberry pi 2, connect p10 pins in gpio25, gpio12, gpio16, gpio13 & gpio26. now, i'm finish circuit , don't know must connect p10's vcc & ground (red & black wire). can me? , code in python controlling p10(1r)-v706 dot matrix?.. regards, kedi i can't python code (did mine in basic on risc os) regarding power, panels each require 2.5a, you'll need separate supply them. if attempted power them pi, pi's polyfuse blow immediately. alternatively, use supply capable of giving 10a supply both panels , pi. raspberrypi
Read more

TypeError: <unknown> is not a numpy array - Raspberry Pi Forums

-
hi, thank help. question simple: how convert raspistill data opencv processing. code: select all def capture(settings, width, height): command = "raspistill %s -w %s -h %s -t 200 -e bmp -n -o -" % (settings, width, height) imagedata = stringio.stringio() imagedata.write(subprocess.check_output(command, shell=true)) imagedata.seek(0) im = image.open(imagedata) buffer = im.load() imagedata.close() return im,buffer code: select all image1, buffer1 = capture(camerasettings, testwidth, testheight) cv2.imshow('image',image1) want use different opencv processing techniques, before need know doing wrong. bests svato raspberrypi
Read more

datso and removing imagetitle - Joomla! Forum - community, help and support

-
hello everybody i have installed datso v. 1.3.8 , remove imagetitles http://www.galleri-kbh.dk/index.php?opt ... ry&catid=2 on datsos  homepage there no names, can't find function in parameters in administration?? http://www.datso.fr/datsogallery/viewcategory/2.html can me. vh jan found way it  :d delete line 307 "$tle = ereg_replace('"', '', $row1->imgtitle);" in file components/com_datsogallery/datsogallery.php Board index Joomla! Older Version Support Joomla! 1.0 Extensions - 1.0.x Components
Read more