Security Announcements: RSS feed? - Joomla! Forum - community, help and support

-

great see forum addresses security announcements. see  there's rss feed this:

http://forum.joomla.org/index.php?type= ... ;board=372

though looks element in feed little vague.

http://forum.joomla.org/index.php

which can/will confuse feed readers (bloglines giving me joomla forum posts -- not security announcements).

anyone know who's in charge of feed?

thanks,

dave

thanks inquiry.

for me link correctly shows intended forum. perhaps try few of these:
if feed reader not rss 0.93, can use rdf (type set rdf), atom 0.3 (type set atom), rss 2.0 (rss2), , proprietary format more information (by not setting @ all.)





Comments

Post a Comment

Popular posts from this blog

Connecting Raspberry Pi 2 to P10(1R)-V706 LED Dot Matrix - Raspberry Pi Forums

-
Image
hello everyone, name kedi.. make system connecting raspberry pi 2 , arduino uno arduino adc of 1 dust sensor sharp gp2y1010au0f , 4 gas sensor. want show decision of air quality system in running text @ p10 16x32 led dot matrix display. in raspberry pi 2, connect p10 pins in gpio25, gpio12, gpio16, gpio13 & gpio26. now, i'm finish circuit , don't know must connect p10's vcc & ground (red & black wire). can me? , code in python controlling p10(1r)-v706 dot matrix?.. regards, kedi i can't python code (did mine in basic on risc os) regarding power, panels each require 2.5a, you'll need separate supply them. if attempted power them pi, pi's polyfuse blow immediately. alternatively, use supply capable of giving 10a supply both panels , pi. raspberrypi
Read more

TypeError: <unknown> is not a numpy array - Raspberry Pi Forums

-
hi, thank help. question simple: how convert raspistill data opencv processing. code: select all def capture(settings, width, height): command = "raspistill %s -w %s -h %s -t 200 -e bmp -n -o -" % (settings, width, height) imagedata = stringio.stringio() imagedata.write(subprocess.check_output(command, shell=true)) imagedata.seek(0) im = image.open(imagedata) buffer = im.load() imagedata.close() return im,buffer code: select all image1, buffer1 = capture(camerasettings, testwidth, testheight) cv2.imshow('image',image1) want use different opencv processing techniques, before need know doing wrong. bests svato raspberrypi
Read more

RC Receiver into Arduino as PC Controller (UnoJoy)

-
my plan take rc car transmitter & receiver connect receiver arduino , convert raw data on pwm 2 channels usable joystick can use on pc play vrc pro (virtual rc pro). however i'm trying troubleshoot why arduino jumping around when set joystick using unojoy . current code this. code: [select] #include "unojoy.h" const int numreadings = 16; int ch1index = 0; int ch2index = 0; int ch1t = 0; //channel 1 total int ch2t = 0; //channel 2 total int ch1a = 0; //channel 1 average int ch2a = 0; //channel 2 average int ch1raw[numreadings]; //raw ch1 data int ch2raw[numreadings]; //raw ch2 data int ch1 = 0; //final ammount /255 int ch2 = 0; //same ch2 void setup(){   setuppins();   setupunojoy();   (int ch1read = 0; ch1read < numreadings; ch1read++)     ch1raw[ch1read] = 0;   (int ch2read = 0; ch2read < numreadings; ch2read++)     ch2raw[ch2read] = 0; } void loop(){   // getting fresh data   dataforcontroller_t contr...
Read more