Skip to main content

Thread: ioctl(SIOCSIFFLAGS) failed: Unknown error 132: Aircrack

-

i trying test wireless ap aircrack-ng, , using beta version of karmic koala. have dell laptot 1390 wireless network card , use b43 driver. according aircrack-ng website, not need apply patches driver, extract firmware. whenever try run aircrack related commands terminal (such "sudo airomon-ng start wlan0") error message ioctl(siocsifflags) failed: unknown error 132. think related incorrect firmware extracted lib/firmware directory. have no idea how solve this, though, appreciated. lot.

same problem here. upgraded jaunty (2.6.28-15 kernel) , airmon-ng gives me following error:
code:
$ sudo airmon-ng start wlan0 interface	chipset		driver wlan0		broadcom	b43 - [phy0]siocsifflags: unknown error 132 				(monitor mode enabled on mon0)
i removed b43-fwcutter (purge) , reinstalled it, rebooted, still same message. wireless works normal though.
using broadcom 4318 on acer aspire 5003.


seems made stupid mistake... on old kernel didn't matter if had wireless switch turned off. airmon-ng start normally, kismet (or other progs) not receive packets. turn on. gives "unknown error 132".
after turning wlan switch on functions , airmon-ng / kismet start before.


Forum The Ubuntu Forum Community Ubuntu Official Flavours Support Networking & Wireless [ubuntu] ioctl(SIOCSIFFLAGS) failed: Unknown error 132: Aircrack


Ubuntu

Comments

Post a Comment

Popular posts from this blog

Connecting Raspberry Pi 2 to P10(1R)-V706 LED Dot Matrix - Raspberry Pi Forums

-
Image
hello everyone, name kedi.. make system connecting raspberry pi 2 , arduino uno arduino adc of 1 dust sensor sharp gp2y1010au0f , 4 gas sensor. want show decision of air quality system in running text @ p10 16x32 led dot matrix display. in raspberry pi 2, connect p10 pins in gpio25, gpio12, gpio16, gpio13 & gpio26. now, i'm finish circuit , don't know must connect p10's vcc & ground (red & black wire). can me? , code in python controlling p10(1r)-v706 dot matrix?.. regards, kedi i can't python code (did mine in basic on risc os) regarding power, panels each require 2.5a, you'll need separate supply them. if attempted power them pi, pi's polyfuse blow immediately. alternatively, use supply capable of giving 10a supply both panels , pi. raspberrypi
Read more

TypeError: <unknown> is not a numpy array - Raspberry Pi Forums

-
hi, thank help. question simple: how convert raspistill data opencv processing. code: select all def capture(settings, width, height): command = "raspistill %s -w %s -h %s -t 200 -e bmp -n -o -" % (settings, width, height) imagedata = stringio.stringio() imagedata.write(subprocess.check_output(command, shell=true)) imagedata.seek(0) im = image.open(imagedata) buffer = im.load() imagedata.close() return im,buffer code: select all image1, buffer1 = capture(camerasettings, testwidth, testheight) cv2.imshow('image',image1) want use different opencv processing techniques, before need know doing wrong. bests svato raspberrypi
Read more

datso and removing imagetitle - Joomla! Forum - community, help and support

-
hello everybody i have installed datso v. 1.3.8 , remove imagetitles http://www.galleri-kbh.dk/index.php?opt ... ry&catid=2 on datsos  homepage there no names, can't find function in parameters in administration?? http://www.datso.fr/datsogallery/viewcategory/2.html can me. vh jan found way it  :d delete line 307 "$tle = ereg_replace('"', '', $row1->imgtitle);" in file components/com_datsogallery/datsogallery.php Board index Joomla! Older Version Support Joomla! 1.0 Extensions - 1.0.x Components
Read more